| ladsm.com http://ladsm.com/forum/ |
|
| throwing cel? http://ladsm.com/forum/viewtopic.php?f=5&t=11722 |
Page 1 of 1 |
| Author: | brendon97 [ Mon Aug 09, 2010 11:45 pm ] |
| Post subject: | throwing cel? |
Uploaded with I have a 1997 eclipse gsx, and i was wondering if i go this route with my vacuum lines will it throw cel. i have herd it wont but i would like to double check. thank you! |
|
| Author: | RiG [ Tue Aug 10, 2010 11:06 am ] |
| Post subject: | Re: throwing cel? |
I cant see the pic at work but if its the taboo speed shop vaccum line routing, then no you wont throw a CEL. If your EGR valve isnt hooked up, make a block off plate for it. It wont throw a CEL, but the code will be there if you ever decide to check your codes or you get another CEL from something else. Its not a big deal and doesnt affect anything. EDIT: I have all extra vaccum lines removed, and my EGR is blocked off. No CELs |
|
| Author: | Black_gst [ Tue Aug 10, 2010 11:26 am ] |
| Post subject: | Re: throwing cel? |
i had mine on my old 97 like that and once every like 6 months it would throw the egr temp sensor CEL but a quick reset and it would be another 6 months or so with no problems |
|
| Author: | brendon97 [ Tue Aug 10, 2010 3:32 pm ] |
| Post subject: | Re: throwing cel? |
ok thank u i was readeing up and it was two sided some people were saying yes and others were saying no. can anyone answer one more question. i am wondering what is the benefit of doing this is it a plus, or equal effect of stock? |
|
| Author: | Synthetek [ Tue Aug 10, 2010 5:11 pm ] |
| Post subject: | Re: throwing cel? |
Its not really going to increase performance or anything. It helps if your using an aftermarket intake manifold or throttle body that doesn't have anyplace to hook up all that emmisons stuff. |
|
| Author: | RiG [ Tue Aug 10, 2010 8:05 pm ] |
| Post subject: | Re: throwing cel? |
My car is a 96 and has never thrown a code for the EGR. I also have a 95 EPROM ECU now and it has never thrown a EGR CEL. It might be the newer cars that do occasionally. I did it to help eliminate vaccum/boost leaks. It also cleans it up a bit but didnt notice any performance gains. |
|
| Author: | brendon97 [ Tue Aug 10, 2010 10:03 pm ] |
| Post subject: | Re: throwing cel? |
thank you I'm doing it for that reason hoses keep getting leaks and i think it looks so messy. and what would u recommend using to block of the egr valve i herd a soda can works, would it be best just to get a egr valve? |
|
| Author: | RiG [ Wed Aug 11, 2010 7:24 am ] |
| Post subject: | Re: throwing cel? |
I used a thin piece of aluminum (like a soda can) and traced the stock gasket and then used RTV to seal it up, then I put the stock EGR valve back over the new gasket/block off plate. If you disconnect the vaccum lines, the EGR valve wont work anyway, so you should block it off. |
|
| Author: | brendon97 [ Sun Aug 15, 2010 6:45 pm ] |
| Post subject: | Re: throwing cel? |
OK thank you! if ill give it a try and let u guys know how it works out. |
|
| Author: | Wally [ Sun Aug 15, 2010 7:53 pm ] |
| Post subject: | Re: throwing cel? |
| Author: | RiG [ Mon Aug 16, 2010 9:40 am ] |
| Post subject: | Re: throwing cel? |
Yes you can cap off all the vaccum lines shown (with the red dots) and just leave the sensors plugged in electrically. You do not need to cap the sensor's vaccum lines. |
|
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|